金莎4399

   一、产品简介

抱箍是用一种材料抱住或箍住另外一种材料的构件。它属于紧固件。电力抱箍装置由箍板、翼板、拉结筋板、螺栓及内衬垫构成。抱箍有好多种,杆顶支座抱箍、电缆抱箍、横担抱箍、拉线抱箍等。 一般由左、右两半片抱箍对合后联接而成，左、右两半片抱箍均呈半圆环状，半圆环两端向外弯折，各形成一个安装耳，安装耳上冲得有螺栓连接孔，用缩口螺栓联接安装，主要原材料为扁钢。

二、产品选材

产品主材选用GB/T 700-2008标准Q235材质钢材，材料抗拉强度≥400Mpa。

三、产品分类

3.1杆顶支座抱箍

杆顶支座抱箍，安装在电杆杆顶，分为单顶单抱、双顶单抱、单顶双抱及双顶双抱，用于10KV及以下线路。

单顶单抱、双顶单抱、单顶双抱、双顶双抱

3.2 拉线抱箍

拉线抱箍是线路中拉线来固定电杆，有扁抱、加强扁抱、双拉线抱箍及四拉线抱箍等。一般用扁钢的规格和所抱杆件的直径来表示其规格，如：-60×6×150。

扁抱、加强扁抱、双拉线抱箍、四拉线抱箍

3.3 导线抱箍

导线抱箍分导线抱箍及导线拉线抱箍，用于电力线路挂线、导线、拉线或同时导线和拉线。用于110KV及以下线路工程，其根据各个设计自行的编号表示其规格。

挂线抱箍、中导抱箍、三联杆导线抱箍、三联杆导线拉线抱箍

3.4 托担抱箍及托担拉线抱箍

托担抱箍及托担拉线抱箍，用于35KV及以上电力线路中托横担或同时托横担及拉线。两者的区别在于后者比前者多拉线板，其根据各个设计自定的编号表示其规格。

3.5 抬担抱箍

抬担抱箍,即抬抱，用于托抬担的抱箍，其一边安装耳上有2个连接螺孔，一般每付用四套缩口螺栓联接，其规格用所用扁钢规格及所抱杆件位置的直径来表示，如-80×8×280。

3.6 电缆抱箍

电缆抱箍,用于电缆上下杆时固定电缆，其根据固定电缆的数量分为单电缆抱箍、双电缆抱箍及多电缆抱箍，主要区别在于电缆箍的数量级大小不同，其规格用所用材料规格及所抱电杆直径来表示，如：-60×6×320。

单电抱箍、双电缆抱箍

3.7 撑脚抱箍

撑脚抱箍，10kV及以下线路工程中安装撑脚之用，一般有几种，焊板的、焊螺栓、扁抱加强扁抱。其规格用所用原材料规格及所抱电杆直径来表示，如：-60×6×210。

三、生产工艺

材料按生产计划选定材料工艺规定的标准尺寸后，按工艺尺寸经过下料、冲孔、弯曲、焊接等工艺加工完成，等待发货。

1、 Product introduction A hoop is a component that holds or hoops another material with one material. It is a fastener. The electric hoop device is composed of hoop plate, wing plate, tie bar plate, bolt and inner liner. There are many kinds of hoops, such as pole top support hoop, cable hoop, cross arm hoop, stay wire hoop, etc. Generally, the left and right half hoops are connected after closing. Both the left and right half hoops are semicircular, and the two ends of the semicircle ring are bent outward to form an installation ear. Bolt connection holes are punched on the installation ear, and the connection and installation are carried out with necking bolts. The main raw material is flat steel.

2、 Product selection The main material of the product is Q235 steel in GB / T 700-2008 standard, and the tensile strength of the material is ≥ 400MPa.

3、 Product classification

3.1 pole top support hoop The pole top support hoop is installed on the pole top, which is divided into single roof single holding, double top single holding, single roof double holding and double top double holding, which is used for 10kV and below lines. Single top single holding, double top single holding, single top double holding, double top double holding

3.2 stay wire hoop The stay wire hoop is used to fix the pole by pulling wire in the line, including flat holding, reinforced flat holding, double pulling wire holding hoop and four pulling wire holding hoop. Generally, the specification of flat steel and the diameter of the holding bar are used to express the specification, such as: - 60 × 6 × 150. Flat holding, reinforced flat holding, double pulling wire holding hoop and four pulling wire holding hoop

3.3 conductor hoop The wire hoop is divided into conductor wire hoop and wire stay hoop, which is used for hanging wire, conducting wire and pulling wire or at the same time. It is used for 110kV and below line project, and its specification is indicated by its own number according to each design. Hanging hoop, middle guide hoop, triple pole conductor hoop, triple pole wire stay hoop

3.4 bracket hoop and bracket stay wire hoop The supporting arm hoop and supporting arm stay wire hoop are used to support the cross arm or simultaneously support the cross arm and stay wire in 35kV and above power lines. The difference between the two is that the latter has more wire drawing boards than the former, and its specifications are indicated by the number determined by each design.

3.5 lifting hoop The hoop is used to lift the load. There are two connecting screw holes on one side of the hoop. Generally, each pair is connected with four sets of necking bolts. The specification is expressed by the specification of flat steel and the diameter of the position of the holding pole, such as - 80 × 8 × 280.

3.6 cable hoop The cable hoop is used to fix the cable when it is up and down the pole. According to the number of fixed cables, it can be divided into single cable hoop, double cable hoop and multi cable hoop. The main difference is that the cable hoop has different order of magnitude. Its specification is shown by the material specification and the diameter of the pole, for example: - 60 × 6 × 320. Single electric hoop and double cable hoop

3.7 brace hoop There are several kinds of bracing hoop, such as welding plate, welding bolt, flat holding to strengthen flat holding. The specification is expressed by the specification of raw materials and the diameter of the pole, such as: - 60 × 6 × 210.

3、 Production technology After selecting the standard size of material process according to the production plan, the material is processed by blanking, punching, bending, welding and other processes according to the process size, waiting for delivery.